隨著工廠搬遷日益增多，許多不規范的操作導致了多起事故不應該的發生，我北京精密設備搬運給大家分享下下例案例。

With the increasing relocation of factories, many non-standard operation led to a number of accidents should not happen, I Beijing precision equipment handling to share with you the next case.

在2008年3月12日晚，某一車間新入職的叉車司機小趙， 因在駕駛叉車轉運混合氣瓶時，駕車途經在經過放著鋼板的安全通道時，看見地面有障礙物，于是就將整筐氣瓶抬至離地約2M高的距離，當司機駕駛著叉車在放有鋼板的通道上來行使時，由于路面不平導致叉車來回顛簸以至于整筐混合氣瓶從兩米高的距離掉到地面，促成了事件的發生

On the evening of March 12, 2008, new recruits a workshop forklift driver Zhao, because in driving forklift transport mixing cylinders, after driving through the security channel with steel plate, saw the ground obstacles, so will the whole basket of cylinders lifted to a height of about 2M distance from the ground, when the driver drove have forklift plate in put up channel when the exercise of the uneven road leads to the whole basket that forklift jerking back and forth mixing cylinder two meters from a distance to the ground, led to the incident

綜合上述的案例，由我們北京精密設備搬運的講師來給大家分析一下他們的事故原因以及相對的解決要點。

Integrated the above case, by our Beijing precision equipment handling of the instructor to give you an analysis of their causes of the accident as well as the relative settlement of the main points.

我們不難看到造成事件發生的直接原是由于叉車劇烈顛簸行駛，物料工框超高運行并且外加物料與插齒沒有任何的緊急鏈接措施。導致了事故的發生。然有因必有果它的間接原因更不能忽視：路面具有障礙物體這一點毋庸置疑，叉車司機可安全意識不強居然為了圖省事隨意操作這應該占主要責任。

It is not difficult to see that the direct cause of the incident is due to the forklift truck violent bumpy driving, the material box is very high and the added material and the gear is not any emergency link measures. Resulted in the accident. However, for there will be indirect reasons for its fruit cannot be ignored: the road with obstacles to this point there is no doubt that the forklift driver can be the strong sense of security even in order to save the main responsibility for this operation should be free.

因此北京精密設備搬運的講師提醒各個工友們， 叉車司機必須經過嚴格的培訓，取得叉車駕駛證后方可行使作用。 叉車在載貨行駛當中時，叉齒不允許離地超過10-30CM否則會發生危險，當叉車停止前進時必須放至到地面上。

Therefore, the Beijing precision equipment handling of the instructor to remind all the workers, forklift drivers must undergo a rigorous training, to obtain a forklift driving license before the exercise of the role. When the forklift truck in the truck, the fork gear is not allowed to leave the ground more than 10-30CM or it will be dangerous, when the forklift must be placed on the ground to stop moving on the ground.